Fractal Design Node 804 Interior

For aesthetic purposes, Fractal Design enriched the black interior of the Node 804 with white accents. The blades of the cooling fans, the five expansion slot covers, and the HDD drive cages are glossy white, creating a striking but clean contrast with the rest of the case.

The motherboard tray can hold up to Micro-ATX motherboards. Instead of multiple small holes, the motherboard tray has just two openings – a massive opening behind the motherboard for the seamless installation of coolers and another to the right for the cables. Note however that the HDD cages will most likely need to be removed in order to reach the back of a motherboard for the installation of a cooler. The vents at the bottom of the left compartment cannot be used for the installation of fans, but two 2.5"/3.5" drives can be secured there using decoupling rubber rings.

The right compartment of the Node 804 is clean and straightforward, with a slot for the PSU at the lower right corner and two cages for up to eight 3.5" drives. The two white drive cages at the top of the cage are removable and can hold up to four 3.5" drives each. Decoupling rubber rings are used at every screw hole to minimize noisy vibrations. 2.5" devices cannot be installed on those two drive cages (without an adapter), limiting the SSD installation options to either the faceplate or the bottom of the left compartment. We should note that 3.5" drives are installed vertically, which makes cable management a little bit difficult, especially with the right cage that brings the drives very close to the PSU.

Vents, vents and more vents. No matter where you look, almost 85% of the whole chassis' exterior surfaces are vents. There are three 120mm fans in the Node 804, with slots for several more if necessary. Fractal Design also boasts that the Node 804 can hold up to four liquid cooling radiators simultaneously; what kind of systems exactly they assumed that would be installed in this case, we cannot imagine. There is a catch though – there are limitations on what radiators can fit and something needs to be sacrificed for each one of them.

For example, 280mm radiators can only fit at the top of the right chamber, but that requires the removal of the HDD cages. If that happens, only one HDD cage can be relocated to the bottom of the compartment and secured using the straps that normally are for cable management. At the top of the left compartment, only 240mm radiators will fit and they will also limit the height of memory modules to 48mm (and removing/installing RAM will require the removal of the radiator). Installing radiators at the front of the chassis limits the length of the expansion cards and prevents the installation of fans at the first slot of the top panel.

Black cables and parts are easily hidden inside an all-black chassis; therefore, for visual clarity, we are using an AX760i PSU with a red cable pack and white SATA cables for our pictures. Building a system inside the Fractal Design Node 804 is a fairly easy – as long as the system is relatively simple, without too many components. The addition of liquid coolers, too many drives ,and/or dual GPU setups could easily cause a stressful mess of things inside such a small case. Most of the time required to build a system should be for the routing of the cables. There are no sharp and or dangerous points about the Fractal Design Node 804 that we could locate during our experience with it.

As exhibited in the pictures of our test build, all of the cables are routed through the opening near the front of the case. This calls for a bit more careful planning regarding the cables near the bottom of the motherboard, but a few cable ties and patience can work marvels. The CPU 12V cable can go through a small opening at the top left side of the motherboard tray. Graphics cards up to 320mm can fit but cards longer than 280mm will partially block the opening for the cables and restrict the installation of an additional intake fan. Also, remember that CPU coolers taller than 160mm will not fit – and that is just about every top performance air cooler available today.

Fractal Design Node 804 Exterior Testing and Results
Comments Locked


View All Comments

  • imaheadcase - Wednesday, February 18, 2015 - link

    You made a error under Specs, it does NOT support ATX. Just mini/micro atx.
  • stlouis1 - Wednesday, February 18, 2015 - link

    I actually built an i7 right with dual GTX 970's in one of these cases for a friend recently. My friend picked the case which I was skeptical about, but although I wouldn't buy it for myself, it's lived up to my expectations of a Fractal Design case, and I admit, it grew on me during the build process. I would recommend it for anyone interested in its aesthetics.
  • bobbozzo - Wednesday, February 18, 2015 - link

    12" high seems too tall for an HTPC to fit in most A/V shelving (standard components are 7" or less).

    Thanks for the review; I have the Node 304 (firewall / UTM) and really like it.
  • romrunning - Wednesday, February 18, 2015 - link

    In regards to fan filters, how hard is it for mfgs to build in filters for their cases that are externally accessible? They should all be simple pull-outs, with a small tab as your handle to pull them out. I don't want to have to disassemble my case or pull off the front cover just to clean a filter.
  • The_Assimilator - Wednesday, February 18, 2015 - link

    Not sure why Fractal didn't just go with a pair of standard 4x 3.5" drive cages with trays they use on their larger cases, and mount them to the roof.
  • Biln3 - Wednesday, February 18, 2015 - link

    This review makes me want to buy 4 cases of coca cola
  • AnnonymousCoward - Wednesday, February 18, 2015 - link

    So uhh, where are the fractals? Just a name I guess.
  • spe1491 - Thursday, February 19, 2015 - link

    I'm interested in this case, but I'm curious about what optical drives would work with it. Doing a quick check on Newegg I don't even see a slim slot loading drive available.
  • neo_1221 - Friday, February 20, 2015 - link

    It looks like a mini-fridge...
  • piasabird - Friday, February 20, 2015 - link

    How about putting things in inches if this is an article or a product in the USA? I would consider it a courtesy to the country you are doing business in.

Log in

Don't have an account? Sign up now